收藏本站
Using The MON08 Debug Port
Establishing Communication Through The MON08 Debug Port
CAUTION
Make sure to connect ribbon cable so that striped side of cable lines up
with pin 1 of interface connector.
5. Connect other end of 16-pin ribbon cable to MON08 port of target board
CAUTION
Make sure to connect ribbon cable so that striped side of cable lines up
with pin 1 of MON08 port of board or that all the board connections are
appropriate for the specific MCU you are using.
6. Connect power cable to FSICEBASE
a. Connect round end of 5-volt power cord to barrel connector on FSICEBASE
b. Plug power supply into surge-protected strip
c. Connect surge-protected strip to AC outlet
7. Switch on power switch of FSICEBASE
The FSICEBASE is now ready to provide communication between a target device and a
host computer through the MON08 debug port.
Establishing Communication Through The
MON08 Debug Port
To establish communication between your host computer and the FSICEBASE, you will
need to install the CodeWarrior software, create a project, and start the debugger. The
following procedure assumes that have installed the CodeWarrior software and created a
project.
When you use the New Project Wizard to create a project in the IDE, the last page of the
wizard (Figure 4.1) allows you to specify the connection information that you want the
project to contain. If you check the P&E Hardware Debugging checkbox, the wizard
adds a build target to your project that is configured to connect through P&E Hardware.
This includes support for connecting through a MON08 debug port.
If you did not include the P&E Hardware Debugging connection when you created your
project, your project does not automatically contain a build target for that connection.
Freescale In-Circuit Emulator Base User Manual, Rev. 1.1
50
Freescale Semiconductor
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
FT24C02A-5LR-T IC EEPROM 2KBIT 1MHZ SOT23-5
FT24C16A-UMR-B IC EEPROM 16KBIT 1MHZ 8MSOP
FT24C256A-UMR-B IC EEPROM 256KBIT 1MHZ 8MSOP
FT24C512A-UDR-B IC EEPROM 512KBIT 1MHZ 8DIP
FT24C64A-UMR-B IC EEPROM 64KBIT 1MHZ 8MSOP
FT822AA IC LED DRVR PFC LOW TDH 8SOP
FT881A IC LED DRVR 30W 8SOP
FT93C46A-ITR-B IC EEPROM 1KBIT 2MHZ 8TSSOP
相关代理商/技术参数
FSICECBLBSA 功能描述:仿真器/模拟器 BUS ANALYZER CABLE RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICECBLBSAE 功能描述:仿真器/模拟器 BUS ANALYZER CABLE RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITAP64 功能描述:仿真器/模拟器 FSICE EMULATOR KIT FOR 9 RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITASAZ 功能描述:仿真器/模拟器 FSICE EMUL FOR 908ASAZ RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITEY 功能描述:仿真器/模拟器 FSICE EMULATOR KIT FOR 9 RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITGPGT 功能描述:仿真器/模拟器 FSICE EMULATOR KIT FOR 9 RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITGRGZ 功能描述:仿真器/模拟器 FSICE EMULATOR KIT FOR 9 RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
FSICEKITJB8 功能描述:仿真器/模拟器 FSICE EMUL FOR 908JB8 RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2